| Wingspan: | 427mm (16.8 inch) |
| Wing Area: | 4.8 sq dm (74.0 sq inch) |
| Length : | 494mm (19.4 inch) |
| Weight without Battery: | 28.0 g (0.98 oz) |
| Weight with LiPo Battery: | 32.5 g (1.20 oz) |
| Motor: | 8.5mm Coreless Brushed (installed) |
| Receiver: | Spektrum AR6400L ultra micro receiver/ESC unit (pre-installed) |
| Servos: | Elevator and Rudder servos on the AR6400L with 2 independent Spektrum AS2000L long-throw ultra micro aileron servos (pre-installed) |
| Battery: | 1S 3.7Volt 150mAh 12C Li-Po (included) |
- Ultra micro size capable of 3D in an indoor
space
- Laser-cut flat foam structure and carbon
reinforcement, a lighter structure results in
high-performance 3D flight in an indoor space
- Removable SFG’s quickly add extra side
areaor increased slow speed knife-edge
performance
- Two independent aileron servos for better
control response and authority
- 4-channel control provides full 3D aerobatic
capability
- Designed by Pilot Seth Arnold 2009 ETOC
Champion
- E-flite LiPo charger –for quick and easy on
location charging
- Complete and ready to fly- simply bind to your
transmitter
- DSM2 architecture, can be used with all
DSM2 transmitters
| EFLU1053 | 3D Gearbox with Prop Shaft |
| EFLU1055 | 3D Landing Gear with Mounts |
| EFLU1056 | 3D Hardware Set |
| EFLU1057 | 3D Wing Bracing with Mounts |
| EFLU1070 | 3D Replacement Airframe |
| EFL9051 | Prop with Spinner (2) |
| EFL9052 | Main Motor |
| EFL9054 | Prop Shaft With Gear (2) |
| EFL9056 | Pushrod Set |
| SPMAS2000L | Long throw servo |
| EFLH1066 | Replacement Servo Mechanics |
| EFLH4070 | Replacement Servo Retaining Collars |
version
Battery:
1S 3.7V 150 mAh 12C LiPo (EFLB1501S)
Charger:
DC LiPo charger (EFLC1003) or a Celectra
4-Port 1S DC LiPo charger with AC adaptor (EFLC1004AC)
Transmitter:
DSM aircraft transmitter with dual rates and
expo.
 |
|||
 |
A 1S 3.7Volt 150mAh
|
||
EFLU1080 UMX Extra 300 3D BNF The Ultra Micro eXtreme (UMX) Extra 300 3D takes the idea of a 3D plane you can fly almost anywhere and turns it into a reality. With a flying weight of 33 grams (barely over an ounce), battery and all, it is slow and light enough to fly extreme 3D manoeuvres in spaces no larger than a dining or conference room. It features an ingenious laser-cut foam airframe, designed by ETOC champ Seth Arnold. The open-frame structure is covered with a micro-thin film and it uses a fraction of the foam material usually used in profile planes of this type. This super light airframe is reinforced with carbon fibre rods that reduce airframe flexing and twisting to a minimum so you can fly the most aggressive 3D manoeuvres with absolute precision. Optional Side Force Generators are also included for enhanced aerobatic performance. These razor-thin pieces of foam slide onto the leading edge of the wing and enhance rudder authority in knife-edge flight. They also improve tracking during precision aerobatics too. The UMX™ Extra 300 3D BNF comes completely assembled with an extremely efficient 8.5mm coreless brushed motor and Spektrum™ AR6400L Ultra Micro DSM2 Receiver/ESC installed. Built-in long-throw servos on the AR6400L drive the elevator and rudder while two independent Spektrum AS2000L long-throw ultra micro servos drive the ailerons. For best performance and to maximise your flying fun a DSM2 aircraft transmitter with dual rates and expo is recommended. |
|||
EFLU1050 UMX Extra 300 3D BNF Basic
|
|||
