| |
 |
 |
| |
|
| Wingspan: |
845mm(32.25inch) |
| Length: |
875mm(34.5inch) |
| Wing Area |
16.8 sq dm (260 sq in) |
| Weight: |
215-260gm(7.5-9.25 ounce) with battery |
| Motor: |
Park 300 or Park 370 outrunner |
| Radio |
6channels |
| Servos |
4 sub-micro servos plus 1 S75 for
VPP option |
| |
|
|
 |
|
| |
 |
| |
- 3mm Depron construction, for strength
and lightness
- Lightweight carbon fibre reinforcing
truss system for maximum strength
- Pre-installed leading edge and trailing
edge flat carbon spars
- Vibrant screen-printed colour scheme
- Ideal for indoor flight, and outdoors
in light winds
- Optional side force generators (SFG)
- Quick and easy assembly, around
three hours
- Suitable for E-flite’s Variable
Pitch Prop System (VPP)
- Ideal match for E-flite’s
Park 300 or Park 370 brushless outrunner motors
|
| |
|
|
|
| |
 |
| |
| EFL1101 |
Pushrods |
| EFL1102 |
Carbon Fibre Stiffeners |
| EFL2305 |
Wheel Pants |
| EFL2306 |
Firewall Mount with Hardware |
| EFL2309 |
Landing Gear
|
| EFLA200 |
Micro Control Horns |
| EFLA203 |
Micro Control Connectors |
| EFLA221 |
Foam Park Wheels, 1.5-inch |
| |
|
|
|
|
| |
 |
Outrunner Setup
EFLM1150 Park 300 Brushless Outrunner Motor, 1380Kv
EFLA1010 10-Amp Pro Brushless ESC
HFL7704 Flightline 8x3.8 Slow Flyer Prop
Or
HFL7707 Flightline 9x4.7 Slow Flyer Prop (George Hicks
setup)
EFLB4303SJ E-Flite 11.V 430mah3 cell Li- Po
EFLC3005 Celectra™ 1–3 Cell Li-Po Charger
Note: If you want more power, substitute the
recommended Park 300 BL Outrunner, 1380Kv
(EFLM1150) with the Park 370 BL Outrunner, 1200Kv with
4mm Hollow Shaft (EFLM1210HS). This motor is not just for
variable pitch props, it has great performance for this
size model.
Variable Pitch Prop Outrunner Setup
EFLPVPP100 Showstopper Precision Variable
Pitch Prop System
EFLM1210HS Park 370 BL Outrunner, 1200Kv with 4mm Hollow
Shaft
EFLA1010 10-Amp Pro Brushless ESC
EFLB0995 E-Flite 11.1V 800mah 3 cell Li-Po
EFLC3005 Celectra 1–3 Cell Li-Po Charger
|
|
|
|
|
|
| |
 |
A precision 3D profile foam model designed
by George Hicks and Jon Leyland the Sobré 3D from
E-flite is a super performer that has superb slow flight
ability coupled with an astonishing 3D aerobatic performance.
The entire model is constructed from 3mm Depron with a vibrant
screen printed colour scheme. Reinforced with carbon-fibre
spars in the wing and fuselage truss bracing to reduce flexing
allows the model to be flown outdoors in low to light winds
of up to ten miles an hour. This reinforcing also gives the
model a lot of added strength for very little weight gain.
The Sobré 3D comes almost ready to fly with
a top quality hardware pack and illustrated assembly
guide, and can be made flight ready in as little
as three to four hours. It’s an ideal match
for E-flite’s Park300 or Park 370 brushless
outrunner motors. And has also been engineered for
use with E-flite’s showstopper variable pitch
propeller system. As if that was not enough, to get
even more outrageous performance with sustained knife-edge
flight, optional side force generators are also included.
Once again, E-flite have got it right with another outstanding
electric 3D model. |
|
 |
|
|
