 |
| Time lost in the pits is always frustrating for any driver and can also lose you that all important track position. Quick pit work and a full tank of gas is all that is required but this is not always the easiest thing to achieve. Fuel foaming in the tank and squeezing the fuel bottle too hard allowing fuel to go over the brakes and the car are always pit lane problems. The Losi fuel gun has been designed to be as user friendly as possible with some nice neat features. When filling the gun the opening uses a fuel tank style mechanism so there is no chance of losing the end or not sealing correctly. When filled the unit is totally sealed so no fuel can spill and you are ready for a pit stop. The trigger assembly is all enclosed so there is no chance of getting your hand caught and slowing up the trigger release system. Then to ensure you have a totally full tank the fuel cut-off tubes are positioned just behind the fuel release nozzle therefore ensuring the tank neck is also full. If the fuel gun is held perfectly upright there will be no fuel spillage at all and a full tank ready to go race ! On the side of the fuel gun there is a graduated scale so you can also see exactly what fuel went into the tank. Plus as the main body is clear you can see the fuel easily and clearly in the gun. You can use the scale to see how much fuel went in to fill the tank, this then also allows you to maximise the next fuel stop potential. |
|
A99070 Team Losi Fast Fueler Fuel Gun |
Rt. 29.99 | ||
There is nothing worse than having your exhaust spring come off during a race or the spring wire snap. This normally occurs because the exhaust spring wire has been crimped by using a pair of pliers to pull the spring into place. This can causes a weak point in the wire, which could so easily have been avoided. By using the Losi exhaust spring tool you can place and attach one end of the spring to the manifold and pull the spring round and into place securely; very easy and a simple tool to use while also reducing the chance of a retirement on race day. |
 |
|
A99166 Team Losi Exhaust spring Tool |
Rt. 8.99 | ||
 |
| The Losi 8ight clutch is regarded as one of the best on the market today with an array of tuning options and varying materials. With both composite and aluminium shoes already available Losi still felt the need to produce a long life shoe. With the incredible loads we put our cars under these long life shoes offer amazing durability while still offering great snap and feeling from the engine. Ideal for truggy racing on high bite and long grass tracks especially when used with a mix of two green and two gold clutch springs. |
|
A9109 8ight/T Long Life Aluminium Clutch Shoes (4) |
Rt. 17.99 | ||
Bearing support is always important and with perfect alignment this can help to produce a vibration free transmission system. The original bearing holder found in the front of the Losi 8ight centre diff mount is made from plastic and therefore may have a small amount of flex. This very simple aluminium ring eliminates all of the flex and offers the bearing maximum support possible. It is essential when fitting this piece to ensure it is seated correctly so as not to place any un-necessary stress on the bearing or to allow the bearing to twist in anyway. A4442 8ight/T Centre Front Aluminium Diff Bearing Adaptor |
 |
 |
With the increasing level of mini RTR cars being produce the need for an entry-level mains charger must be met. This Trickbits 230volt mains charger is ideal for all of your 7.2volt mini race and entry level packs. Simply plug the unit into the wall and check the light for current charge status. Charging at 600mah the top of the range packs will take about two hours to fully charge, lower capacity packs may only take one hour. TB2320 Trickbits 7.2V Mini Pack Charger |
 |
 |
TB1600 |
TB1601 |
| With high torque servos and personal transponders the load and current draw on receiver packs has increased. A good quality high capacity pack is very important to ensure you make it to the end of the race without any problems. The Trickbits 1600mah receiver packs are available in both stick and hump configuration making them suitable for just about any 1/8th buggy, monster truck, truggy, or micro car as a race pack. Supplied with a BEC connector these packs will plug into just about any “Y” harness and receiver socket. Connected together with high quality bars and welded into position for a good strong contact. The packs are also glued together to reduce the chance of any damage to the battery connections. A good pack of receiver cells at a great price. |
|
TB1600 Trickbits 1600MAH Receiver Hump Pack |
Rt. 11.99 Rt. 11.99 |
||
 |
For BSI |
 |
For KO Propo, Fioroni |
 |
For Losi, Trickbits |
 |
 |